Connecting Stand and Speakers. Rear of the PDP. The ferrite cores are used to attenuate undesired signals. To view television channels correctly, a signal must be received by the set from one of the following sources:. Otherwise, the EMI characteristic will become worse because power input and output signals interrupt each other. The component you select should turn on. If it turns on, your remote control is now set correctly. Welcome to ManualMachine.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Do not expose the PDP to direct sunlight and other sources of heat.
Do not expose the PDP to any liquids. Do not step on or twist the power cord. Do not drop the remote control. User Instructions Screen Image retention Do not display a still image such as on a video game or when hooking up a PC to this PDP on the plasma monitor panel for more than 2 hours as it can cause screen image retention.
Cell Defect The plasma display panel consists of fine cells. Height The PDP can normally operate only under m in height. MENU Menu display. Audio outputs for an audio system.
DVD, video game device or video disc players. Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: Purchase the PDP Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it.
Do not mix battery types, i. Check with your dealer. To protect the performance of the PDP and prevent troubles, avoid the followings: - Do not install next to smoke and fire detectors. Use only recommended parts and components. Check with your dealer 1 Check for the stability of the wall where the PDP is to be installed. When the angle has When the angle has When the panel hasn't been set to 5 degrees.
Angle control holes 5 degrees of tilt 10 degrees of tilt 15 degrees of tilt No tilt 20 degrees of tilt. Insert the bolts, dish-type washers, and insulation rubber into the four screw-holes as shown in the figure: Bolt Insulation rubber 5 Hang the protruding plastic part on the rear of the PDP up the groove on the top of the wall attachment panel.
Then, lift down the PDP. Do not lift down the PDP with too much force. The ferrite cores are used to attenuate undesired signals. When connecting cables, attach one of these ferrite cores to the cable near the connector. When you connect the speaker wire, RCA cable and S-Video cable to the connectors, first bind round the ferrite core to secure it. Connecting PDP and Speakers. Fix the bracket onto the guide pole located on the rear of speaker and fasten the screws.
It may damage the bracket clamping the speaker and your PDP together and result in a drop of your PDP and a risk of personal damage and injury. Connecting Stand and Speakers. The main voltage is indicated on the rear of the display and the frequency is 50 or 60Hz. This system makes it convenient and fast to use features on the PDP.
The main menu appears on the screen. Use the joystick left, right button to display, change, or use the selected items. Press the joystick button to enter items in the menu. On screen menus disappear from the screen automatically after about thirty seconds, or you can press the Menu button on the remote control to exit the menu. When you start using your PDP for the first time, you must select the language which will be used for displaying menus and indications.
Result: The options available in the Miscellaneous group are displayed with the Language option is selected. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Do not expose the PDP to direct sunlight and other sources of heat. Do not expose the PDP to any liquids.
Do not step on or twist the power cord. Do not drop the remote control. User Instructions Screen Image retention Do not display a still image such as on a video game or when hooking up a PC to this PDP on the plasma monitor panel for more than 2 hours as it can cause screen image retention. Cell Defect The plasma display panel consists of fine cells. Height The PDP can normally operate only under m in height.
The exclamation point within the! MENU Menu display. MUTE Temporary sound switch-off. Inserting the Batteries in the Remote Control ENG You must insert or replace the batteries in the remote control when you: Purchase the PDP Find that the remote control is no longer operating correctly 1 Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it.
Do not mix battery types, i. Check with your dealer. To protect the performance of the PDP and prevent troubles, avoid the followings: - Do not install next to smoke and fire detectors. Use only recommended parts and components. Check with your dealer 1 Check for the stability of the wall where the PDP is to be installed.
When the angle has When the angle has When the panel hasn't been set to 5 degrees. For a better experience, please enable JavaScript in your browser before proceeding. You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an alternative browser. Its finally here, yes after nearly 8 weeks and a short jail term for disruptive behavior the Samsung Plasma arived today. Sounds great. Is this a better machine than the LG from Comet? Magsy Standard Member. Where is the DVI? On the media box? What is used to pass the signal digitally? Oasis-GasPanic Active Member.
Hi Phil, I've had one on order like yourself for about 8 weeks and am told it will be here on monday. I'm happy to see it accepts Prog Scan because that was the only thing I was unsure on it doing or not.
Cheers, PS. Good luck with setting it up I know I'm gonna need it!!! The screen only has one connector which is dvi I think as it uses same connector It is the media box that contains all the connection options.
The model i recieved seems to be slightly diffent from the one I saw in currys. The manufacture date is 9 of November. The DVI connector is on the back of the media box next to the output for the screen! Ah interesting! If it has svid etc on the back then the screen must have to components to do the linedoubling But if the one you got is missing those connectors then i may well need a box!
Hope ure enjoying it! Kirk Standard Member. Phil, Congratulations on the screen and I am looking forward to hearing your verdicts on the performance of the screen.
0コメント