See Address 16 - Bit 4. Non-add Numbers cannot be printed on No-sale receipts. Non-add Numbers can be printed on No-sale receipts. The Consecutive No.
It is non-resettable. On the first receipt issued after the rest report, the consecutive No. If this status is selected it is recom- mended to take the Daily Financial Reset Report at the end of all operations on the register for the day so that the first receipt will always start with Consecutive No.
Whether or not sale total is printed depends on the selection of Address 1 - Bit 3. Sale total printed excludes taxes. Bit 7: When the Remote Slip Printer is connected and slip is inserted, keying-in will be unconditionally prohibited during issuance of the sale finalization receipt. Any operation is possible with the drawer kept open. SET Status Bit 2: SET status An error will result when the drawer is kept open for the programmed seconds.
Drawer 1 condition is judged during the cashier key OFF status. Bit 3: If SET status is selected, Drawer 1 will be assigned to the cashiers 1 and 2, and Drawer 2 to the cashiers 3 and more. Bit 2: If SET status is selected, the register will operate without any cashier identifying operation. If those reports are not taken before changing the bit to SET status, the cashier memory contents will not be guaranteed.
The following will result if SET status is selected. An error will result on attempt to issue any kind of cashier report. This selection is applied to all the cashier types. Cashier No. For each line, a maximum of 24 regular-sized characters or 12 double-sized characters may be entered. A combination of both types is also available.
The line Nos. If any incorrect characters have been programmed, depress the [C] key to clear all the characters on a line and then re-enter charactrs from the beginning, or end the line with an [ST] and re-program the entire line. The new data will be active. When all the lines have been programmed, do a check by issuing a receipt. Only the lines with errors need to be re-programmed; other lines will not be affected. When blanks are programmed for the whole one line, it will cause one line space.
As for Commercial Message, if blanks are programmed for all three lines, it will cause line feed. However, if the message is programmed for one line, remaining two lines will result in two lines space.
As for the Store Message Print Feature, even if blanks are programmed for all four lines assigned to Store Message, it will not cause line feed. Those lines will result in four lines space. ST Line No. Repeat for another line. For each cashier name, a maximum of 8 regular-sized characters or 4 double-sized characters may be entered. This programming is available only when the cashier identifying operation option has been selected. Number of the controllable cashiers differs as follows.
Preset Price Max. NOTE 1 Repeat for programming other departments max. Department No. DP When an address No. For each department name, a maximum of 8 regular-sized characters or 4 double-sized characters may be entered. Department status available is as follows.
Ordinary Dept. Other Income Dept. Line No. Program Address No. When sequentially programming the PLUs, the code specification can be omitted. If all the PLUs must be deleted i. Time now set a. Issues a receipt. A maximum of 24 hourly ranges may be set. Such setting does not cause an error in programming but the sales data will not be processed into that hourly range. If an hourly value of more than 23 or a minute value of more than 59 is set, it will not result in an error but the data will not be processed into that hourly range.
To change the table of hourly ranges once set, partially or entirely, do the entire setting operation over again. The time to start is the time entered for the preceding Hourly Range. Add to Compare Added to comparison table. General Information Reviews. Ordering via alternative methods If choosing to order via check, Western Union, etc, we will have to wait to receive payment before we authorize the order. Instructions for downloading the file using Apple products If you do not have the Excel app, download it free from the App store.
Once the order confirmation is received with the download link, you can click that button, There is a share button box with upward arrow on the top right corner. Click that button. Next click the green "Copy to Excel" button. It can be programmed to prohibit cashing. They can be programmed to allow cashing.
The drawer opens to enable exchanging the noncash media into cash. The receipt for the last sale is issued. When a sale has contents of 30 print lines or less, the post-issue receipt will be an itemized receipt, just as the ordinary receipt. When it has more than 30 print lines, the postissue receipt will be a total-only receipt. However, the program option allows the register to always issue a total-only receipt regardless of the number of the print lines. If a Non-add Number print is entered at the top of a sale, the number will not be printed on the Post-issue Receipt.
After depressing the [EX] key, the sale must only be finalized for payment through media keys including the [CUR] keys. Tax Exemption transaction cannot be item-corrected. The entered tax amount is printed and added to the sale. The [TAX] key should be used in the single tax area. It should not be used in the dual tax area nor the triple tax area.
TAX4 0. Displays the sale total in the foreign currency. Displays the sale total in the domestic currency. CUR NOTE All the items are entered for the customer. The sale is finalized if over-tendered, or not finalized if short-tendered. When over-tendered: The sale is finalized, the drawer opens, and the change due is displayed in the domestic currency which is to be returned to the customer.
When short-tendered: The sale is not finalized. The final media key must be programmed to allow tendering. A negative-balance sale or a sale of zero cannot be finalized with a Foreign Currency key. CUR 1 NS or Displays the domestic currency amount equivalent to the entered foreign currency amount.
See the sketch below. Before depressing the key, be certain to insert a slip to the Validation Slot. If no slip is inserted, the validation print will occur over the last printed line on the receipt. After validation print, be certain to remove the slip from the Validation Slot. In this case, no other operations can follow until the validation print of the item is performed. The following options are selective in relation to validation print: 1 Print Format a Consecutive No. DP06 Amount The remote slip printer will automatically activate printing when the slip has properly been set to the printer table.
When a slip is properly set to the remote slip printer and the ECR is operated, the gap will be closed and printing will be performed. When the sale is finalized and the receipt is issued, the gap of the DRS will be opened to allow the slip withdrawal. The gap keeps closed during sale item entries. Paper Roll Replacement and Other Maintenance When a red line appears on the edge of the paper roll, follow the steps below to replace the paper roll with a new one.
It may cause a paper jam. Depress the [JF] key to feed the remaining paper end. Apply ink from the shaded places. Stamp may not print dark immediately. Allow time for ink to saturate the stamp. In the event of a power failure or other trouble, the drawer can be opened manually in the following manner.
The drawer will now open. The Drawer Release Key can be taken out by returning it to the original position. Locking When the drawer is closed, it is automatically locked and will not open without the Drawer Release Key or transaction entries. Removing the Drawer 1 Pull the drawer out, and when it stops by the stopper, lift the drawer up and pull it again. Media Slot The Media Slot provided at the front of the drawer is used to put non-cash media such as check in the drawer without opening it.
The non-cash media put from this slot are kept under the Money Case, therefore you can keep them in secret. Media Slot Non-cash media are kept here. Unlocking Unlock the cover using the key, and lift the front end. In Case of the Power Failure If a power failure occurs during business hours, all sales data stored in the memory are automatically protected by the batteries installed in the register. When any data was being printed on the power failure, the same data is automatically printed at the power recovery.
In case of the power failure, it is suggested to check the receipt print contents before you hand the receipt to the customer. MEAT 7. Troubleshooting The following are possible causes and measures against typical troubles.
When a trouble occurs, refer to this chapter to find a cause of the trouble, then take appropriate measures. If a trouble not described here occurs, or a trouble still exists after taking the following measures, ask the store where purchased. In this case, inform the store where purchased of your trouble in details. If you cannot solve a problem with the following solutions, do not attempt to repair it yourself.
Cause 1: Register is not plugged in. Measure: Plug in an outlet. Cause 3: The outlet does not supply the power. Measure: Use another outlet. Trouble concerning Printer Printer does not perform the paper feeding.
Cause 1: Paper roll is not placed correctly. Measure: Place the paper roll correctly. Refer to page Cause 2: Paper fragment or foreign substance blocks the inside of the paper path. Measure: Printer provided for this register is a precision machine, therefore ask the store where purchased.
Cause 3: Failure of the printer itself Measure: Ask the store where purchased. Cause 1: Paper roll is not placed correctly, or placed on the skew. Cause 2: Failure of the printer itself Measure: Ask the store where purchased. Printer prints nothing. Cause 1: Ribbon cassette is not installed. Measure: Install the ribbon cassette. Cause 2: Ribbon cassette reaches its life, deteriorates, or is damaged.
Measure: Replace the ribbon cassette with a new one. Cause 4: Failure of the printer itself Measure: Ask the store where purchased. Printing as a whole is too light. Cause 1: Ribbon cassette reaches its life, deteriorates, or is damaged. Printing gets stained. Cause 1: Printer gathers paper dust. Measure: It is necessary to clean the inside of the printer, therefore ask the store where purchased.
Printing is uneven or too light. Abnormal sound generates. Cause 1: Paper roll or Ribbon cassette is not placed correctly.
Measure: Place the paper roll or ribbon cassette correctly. Refer to page 46 or Stamp does not work. Cause 1: Stamp is not installed correctly.
Measure: Install the stamp correctly. Cause 2: Failure of the stamp mechanism Measure: Ask the store where purchased. Print of the stamp is too light. Cause 1: Stamp ink is not enough.
Measure: Replenish the ink. Cause: Paper roll is placed on the skew, or foreign substance exists in the paper path of the inside of the printer. Measure: Remove the jammed paper as follows. After removing it, return the upper side of the printer until it clicks. Trouble concerning Keyboard Key on the keyboard does not function.
Cause 2: Failure of the keyboard itself Measure: Ask the store where purchased. Trouble concerning Drawer Drawer does not open. Cause 1: Drawer catches foreign substance coin, etc. Measure: Try to open the drawer by removing the foreign substance, using a ruler or something. If not effective, ask the store where purchased. Cause 2: Failure of the drawer itself Measure: Ask the store where purchased. Trouble concerning Display Display displays nothing.
Cause 1: Register is not securely plugged in. Measure: Securely plug in an outlet. To clear the error, return the Control Lock to the original position. Error caused by changing the Control Lock position cannot be cleared by the [C] key. Normal operations cannot be carried out. Cause 1: Control Lock position does not correspond to the operation you attempted.
Measure: Check whether or not the Control Lock position corresponds to the operation. Especially, check whether or not the operation you attempted requires the MGR position. Ask your manager about the operations which requires the MGR position.
Error tone beeps Cause 1: Operation procedure is incorrect. Measure: Depress the [C] key to clear the error, then check the operation procedure you attempted. Cause 2: Control Lock position is incorrect.
Cause 3: Operation in the REG position was attempted while the drawer remained open. In case that the Drawer-close Compulsory Option has been selected.
Measure: Close the drawer, then depress the [C] key. Cause 3: Operation was attempted while the drawer remained open. Cause 4: Operation you attempted requires the MGR position. Cause 5: You ignored the validation print when the Validation Compulsory Option has been selected to the last operation you attempted. Measure: Depress the [C] key, and perform the validation print. Cause 6: After performing the validation print, you attempted the next operation while the validation slip remained in the validation slot.
Share Your thoughts with the other users. User ratings and reviews for this file: Date User Rating Comment. Schematics 4 Free. Service manuals, schematics, documentation, programs, electronics, hobby
0コメント